安装芯片式和刷卡式读卡器
芯片式和刷卡式读卡器带有两张安装贴纸，您可将其用于粘贴到其他设备（如手机或平板电脑的背面）或光滑的平面上。如果您拆下芯片式和刷卡式读卡器，则可以将安装贴纸擦干净并重复使用。
在安装贴纸之前清洁安装表面和芯片式和刷卡式读卡器，以确保粘贴牢固。
安装芯片式和刷卡式读卡器：1. 从安装贴纸的一侧撕下保护膜。2. 将安装贴纸粘贴在芯片式和刷卡式读卡器的背面（没有 logo 的一面）。3. 撕下安装贴纸上剩余的保护膜。4. 按住安装面上芯片式和刷卡式读卡器的贴纸侧，保持 3 秒。
打开和关闭芯片式和刷卡式读卡器的电源
若要打开芯片式和刷卡式读卡器，请按下并释放读卡器侧面的电源按钮。状态灯将亮起。如果您已将读卡器与您的 POS 设备进行了配对和连接，此读卡器会自动连接到您的设备。
在处于非活动状态 30 秒后，芯片式和刷卡式读卡器将进入待机模式，状态指示灯每 5 秒闪烁一次。在待机模式下，如果在结账时接受卡付款，读卡器会自动开启。
在处于非活动状态 3 小时后，芯片式和刷卡式读卡器自身会完全关闭。当您下次想通过卡收费时，您需要再次按下电源按钮然后松开以打开读卡器。通常情况下，您一天只需要打开一次读卡器。您随时可以手动关闭读卡器：长按住电源按钮，直到状态灯熄灭。
芯片式和刷卡式读卡器的状态指示灯
每当打开芯片式和刷卡式读卡器时，状态指示灯会显示读卡器的连接状态以及读卡器是否需要充电：
| 持续闪烁 | 读卡器已准备好连接到 POS 设备。 |
| 每 5 秒闪烁一次 | 读卡器处于待机模式。 |
| 绿色 | 读卡器已充电。 |
| 黄色 | 读卡器正在充电。 |
| 红色 | 读卡器的电池电量为 10%，应对读卡器进行充电。 |
| 无光 | 读卡器已关闭。 |
当状态指示灯变为红色时，您可以继续进行销售，但应尽快为读卡器充电。
Shopify商户官网原文详情：
Mount the Chip & Swipe Reader
The Chip & Swipe Reader comes with two mounting stickers, which you can use to attach it to another device (such as the back of a cellphone or tablet) or a smooth, flat surface. If you detach your Chip & Swipe Reader, then the mounting sticker can be wiped clean and re-used.
Clean the mounting surface and the Chip & Swipe Reader before attaching the mounting sticker to ensure a strong bond.
To mount the Chip & Swipe Reader: 1. Remove the protective film from one side of the mounting sticker. 2. Attach the mounting sticker to the back of the Chip & Swipe Reader (the side with no logo). 3. Remove the remaining protective film from the mounting sticker. 4. Press the sticker side of the Chip & Swipe Reader against the mounting surface and hold for 3 seconds.
Power the Chip & Swipe Reader on and off
To turn on the Chip & Swipe Reader, press and release the power button on the side of the reader. The status light turns on. If you've already paired and connected the reader with your POS device, then the reader automatically connects to the device.
After 30 seconds of inactivity, the Chip & Swipe Reader goes into standby mode, and the status light flashes every 5 seconds. While in standby mode, the card reader turns on automatically when you take a card payment at checkout.
After 3 hours of inactivity, the Chip & Swipe Reader turns itself off fully. When you next want to take a card payment, you need to press and release the power button to turn on the card reader again. Typically you need to turn on the card reader only once a day. You can manually turn off the reader at any time by pressing and holding the power button until the status light turns off.
The Chip & Swipe Reader status light
Whenever the Chip & Swipe Reader is turned on, its status light shows the reader's connection status and whether the reader needs to be charged:
Continuous flashing The card reader is ready to connect to a POS device. Flashing every 5 seconds The card reader is in standby mode. Green The card reader is charged. Yellow The card reader is charging. Red The card reader's battery is at 10% and the reader should be charged. No light The card reader is turned off. You can continue to make sales when the status light turns red, but you should charge the reader soon.
文章内容来源：Shopify商户官方网站
