在哪里购买 Chipper 2X BT 读卡器
Chipper 2X BT 读卡器仅在美国的 Shopify 硬件商店中销售。
打开和关闭 Chipper 2X BT 读卡器
若要打开 Chipper 2X BT 读卡器，请按下其电源按钮然后松开。状态指示灯将亮起，等待状态指示灯变为蓝色。如果您已将读卡器与您的 POS 设备进行了配对和连接，则读卡器会自动重新连接到您的设备。
芯片式读卡器没有其他读卡器所具有的睡眠模式。但在处于非活跃状态 30 秒后，Chipper 2X BT 读卡器会进入待机模式。在待机模式下，读卡器仍会连接到您的 iOS 设备，并且会在您恢复活动时自动退出待机模式。若要恢复活动，您需要按下并释放电源按钮，然后即可再次使用读卡器。如果您按住电源按钮 4 秒或更长时间，读卡器会重置之前的任何蓝牙配对，并且您需要再次将读卡器与设备配对。在处于非活跃状态 10 小时后，读卡器会自动关闭。若要手动关闭读卡器，请按住电源按钮，直到状态指示灯熄灭。您无需为节省电量而关闭读卡器。
为 Chipper 2X BT 读卡器充电
您可以使用随附的 USB 线缆来为 Chipper 2X BT 读卡器充电。若要为读卡器充电，请将 USB 接口较小的一端插入读卡器，然后将较大的一端插入手机充电器或计算机。
Chipper 2X BT 读卡器需要 3-4 个小时即可充满电。在读卡器充满电后，其电池可持续支持一周的销售。
当 Chipper 2X BT 电量低时，状态指示灯将变为红色。
Shopify商户官网原文详情：
Where to buy the Chipper 2X BT card reader
The Chipper 2X BT card reader is available from the Shopify Hardware Store in the United States.
Power the Chipper 2X BT card reader on and off
To turn on the Chipper 2X BT card reader, press and release its power button. The status light indicator turn on, wait until the status light turns blue. If you've already paired and connected the reader with your POS device, then the reader automatically reconnects to the device.
The Chipper does not have a sleep mode akin to our other readers. Rather, after 30 seconds of inactivity, the Chipper 2X BT card reader will go into standby mode. The reader stays connected to your iOS device while in standby mode and automatically exits standby mode when you resume activity. In order to resume activity, you need to press and release the power button use the card reader again. If you press and hold the power button for 4 seconds or more, then the reader resets any Bluetooth pairing that it had, and you need to pair the card reader with the devices again. The reader automatically turns off after 10 hours of inactivity. To turn the reader off manually, press and hold the power button until the status light goes out. You don't need to turn the reader off to conserve power.
Charge the Chipper 2X BT card reader
You can charge the Chipper 2X BT card reader by using the USB cable that's supplied with it. To charge the reader, plug the small end of the USB connector into the card reader, and then plug the large end into a phone charger or computer.
The Chipper 2X BT card reader takes 3-4 hours to charge fully. After the reader's fully charged, its battery should last for a week of selling.
When the Chipper 2X BT has a low battery charge, the status light turns red.
